温拌LDPE改性沥青混合料性能研究

选择Sasobit和Evotherm 3G两种温拌剂对温拌LDPE沥青混合料制备工艺和性能进行研究。首先,比较变温等体积法和等黏温度法两种方法,并确定两种温拌混合料的拌和及击实温度。在此基础上,分别采用车辙试验、低温弯曲试验、中点加载弯曲试验以及冻融劈裂试验评价70#、LDPE、Sasobit-LDPE以及3G-LDPE四种沥青混合料的高温性能、低温性能、疲劳性能和水稳定性。结果表明,两种温拌技术均是可行的,Sasobit和3G温拌技术可使施工温度降低20℃和15℃。与热拌LDPE沥青混合料相比,Sasobit温拌沥青混合料具有更好的高温性能和水稳定性,在高应力比条件下抗疲劳性能更好,低温性能虽变差,但是优于70#沥青混合料;3G温拌沥青混合料的高温性能,低温性能以及水稳定性则与热拌LDPE沥青混合料各项性能较为接近,抗疲劳性能变差,但是优于70#沥青混合料。     

On the thermal conductivity of bimodal SiC/A356 composites fabricated via powder metallurgy route

The present study investigates the thermal conductivity of bimodal SiC particulate distribution in aluminum matrix composites fabricated via powder metallurgy route. The effects of the SiC_p reinforcement size distribution and processing parameters such as sintering time and temperature on the thermal conductivity have been examined. The Box–Behnken experimental array was employed to identify the effects of selected variables on the thermal conductivity of the composite. A reasonable augmentation in the thermal conductivity was observed with an increase in sintering time and %volume fraction of fine SiC particulates. It has been demonstrated that the matrix doped with fine SiC particulates (37?µm) occupied interstitial positions and formed continuous SiC–matrix network resulting in minimizing the micropores that contributed for good thermal conductivity, that is, 235?W/mK. Scanning electron microscopy (SEM) and x-ray diffraction (XRD) were conducted to evaluate the microstructure architecture and interfacial phase formation.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。     

液压阻尼孔的宽温度范围流动特性试验研究

研制一种适合对各种液压孔口或缝隙进行高低温流体力学试验的新型试验装置，运用该装置对具有不同几何参数的液压阻尼孔进行在-50~80℃宽温度范围内的流动特性试验，研究以普通抗磨液压油HM46和低温抗凝减振器油TITAN SAF 5045为工质及其温度变化时对液压阻尼孔流量-压力特性曲线、幂指数和流量系数的影响，研究表明，在低温条件下，液压阻尼孔的流量系数均因油液黏度增大、流动性变差而呈线性下降的趋势，从宏观上看，HM46通过液压阻尼孔时的流动稳定性较差，其对应流量系数的下降幅度明显大于TITAN SAF 5045对应的下降幅度，厚壁小孔流量系数的下降幅度明显大于薄壁小孔对应的下降幅度。研究所获得的新型试验装置、试验数据分析方法和具体理论公式为深入研究和优化现代液压元件在宽温度范围内的动态性能提供新型试验平台与理论基础。     

垂直矩形窄通道启动过程壁温变化特性研究

以去离子水为介质，对竖直矩形窄通道在启动过程中壁面温度的变化规律进行了研究。将一次启动与二次启动时壁面温度的变化特性进行了对比，并改变入口温度，研究了入口温度对启动壁面温度的影响。结果表明：一次启动时壁面温度经过三个阶段，即急剧上升阶段、缓慢升高阶段、缓慢上升至最高壁面温度后又缓慢降至稳态饱和沸腾阶段；二次启动时产生的沸腾滞后现象较一次启动时明显；提高入口温度可增加饱和沸腾段，减少壁面温度的波动，在一定程度上可避免壁面温度过冲对换热器的损坏。     

630℃超超临界二次再热塔式锅炉热力特性与壁温耦合计算研究

630℃超超临界火电技术作为下一代超超临界发电技术,对于煤炭资源的节约、发电机组的经济性以及环境改善,都显示了优越性。目前630℃超超临界锅炉的热力计算还缺乏相关研究。本文以某1000MW超超临界二次再热塔式锅炉布置方案为例,将锅炉管道、炉膛、高温受热面作为串联管路计算,在工质侧将热力计算与管路计算进行耦合建立数值分析模型。该计算模型能够同时得到比实现水动力和热力计算更精细的结果,对后续700℃工程持续优化提升做好技术储备。     

New insight to the oxidation kinetics of silicon-containing steel at high temperature

This study investigated the oxidation kinetics of silicon-containing steel at 1150–1300 °C using a Simultaneous Thermal Analyzer under atmospheric conditions similar to that of an industry reheating furnace. There is a critical time point for the oxidation kinetics at an oxygen concentration of 4·0 vol.-%., following which the oxidation rate constant increases with the increasing oxidation temperature. The model coefficient A in the kinetic oxidation equation was found to be constant. However, before the critical time point, the oxidation rate constant remained unchanged; the model coefficient A decreased with the increasing temperature. Therefore, the kinetic model of silicon-containing steel for isothermal oxidation was observed to be a modified one on the basis of the experimental data. In addition, the critical time point was prolonged with the increasing isothermal oxidation temperature. Moreover, the oxidation activation energy of the tested silicon-containing steel was 366·16 kJ mol^?1.     

油封唇口温度变化对密封性能的影响

基于流量因子统计学方法建立油封唇口的混合流体润滑模型,耦合油封的能量守恒方程及黏温方程,通过迭代求解获得油封唇口的温度分布、不同转速下油封唇口的最高温度及温差变化情况;对比分析考虑和不考虑温差情况下油封各项密封性能。结果表明:随着转速的增大,唇口最高温度线性递增,而唇口温差先增大后减小;油封工作时,唇口区域的温度先迅速升高后下降,越靠近唇尖的位置温度越高;与不考虑温度的情况比较,考虑温度变化的影响时密封区域的油膜厚度减小,油膜承载力下降,不利于密封。     

大方坯结晶器电磁搅拌器结构优化

为改善连铸结晶器内钢液的流动状况，采用有限元法和有限容积法研究了大方坯结晶器电磁搅拌器结构对连铸结晶器内电磁场、流场和温度场分布的影响。结果表明，新型结晶器电磁搅拌器在400 A、3 Hz时产生的电磁力比传统结晶器电磁搅拌器在500 A、3 Hz时产生的电磁力更加均匀，对结晶器内钢液的扰动更强，可提高结晶器内的传热效率，有助于初始凝固坯壳和等轴晶的形成，改善方坯质量。